Replacement UPVC Door Handles

If you're replacing your handles and hinges or adding a little extra security you can find the right handle for your door. These upvc door handles replacement handles are easy to fit and comply with the required 92mm centres for multipoint locks.

The most important measurements to be considered are the backplate fixing centers and key hole dimensions for levers and levers. Check these measurements against your existing measurements prior to ordering.

Lever/Pad

Lever pad handles consist of a lever on one side and a paddle-shaped handle on the opposite. They are designed to be used with key wind locks however, they can also be adapted to split spindle multipoint door locks (though you'll need a separate dual spindle lock case).

Our range of upvc handles lever pads are available in a wide range of finishes. They will be listed in the drop down list once you have found the right handle for your doors. Some styles of handles are not available in all finishes. You should always examine the technical drawing and dimensions sections for the particular item you are looking to ensure that you receive the right fit and size.

When selecting a new set of upvc lever pad door handles it is crucial to make sure that they correspond to the PZ (distance between the spindle of the handle and the center of the cylinder hole) of your existing multipoint locks, as these need to be in line for the doors to remain locked, whether from the inside or outside. The handles we offer are designed to work with most standard cylinder locks, however it is advisable to double glazed windows handles-check before purchasing.

You'll need to take off the handles on your current handle and remove the lock case if you are upgrading to dual spindle levers for your handle as this will require a split inline cylinder. They can be purchased separately, and we provide the complete technical diagram for you to look at in the images for each product.

It is a good idea to loosen the screws that are holding your door handle, and then inspect the mechanism. If the screws are too tight, you may need to loosen them even more. Then you can remove the spindle from the handle and replace it with your new Upvc handle. Before putting the handle in place it is recommended to make sure it is in the proper position, and you can do this by placing your finger in the gap between the door frame and the door handle to ensure that it is level.

Lever/Lever

Lever door handles are an a multi-point lock using the Euro Cylinder and can be found on a majority of upvc double glazed door handles doors, aluminium doors and some wooden doors. They come in two varieties, with the lever inside and a paddle on the outside. Sprung - These have a spring cassette installed within the backplate to help bring the handle lever to the horizontal position. Non-sprung: They do not include a mechanism that can spring the handle lever into a horizontal position.

To repair the door handle lever that is sliding it is necessary to locate the hole or pin that is the detent access point. It's usually a small hole or protruding ring or rectangle found on the handle base plate. Once located you can loosen the set screw with the help of a screwdriver, and then remove it to release the lever to return to the horizontal position.

When the handle is in a horizontal orientation, you can re-install the screws and tighten them so that the handle remains secured to the base plate. It is also advisable to apply an adhesive that locks the screw threads to improve the grip and prevent them from loosing over time.

There are many reasons why lever door handles slide. The most common cause is that the fixings are too tight and the lever bearing to pull against the door. It could also be that the levers may not have been operated at the correct angle, which causes compression of the latch mechanism, preventing it from fully springing into action.

A common cause of a sprung lever not working properly is the spring not being in the proper position on the backplate. The easiest way to test this is to move the handle and see whether it returns to its horizontal position.

If your door handles are loose it is crucial to find the problem quickly, as this can lead to excessive wear on the screws, and even to the handle falling off the base plate. It is recommended to tighten all loose screws on a regular basis, as this will help to stop them from loosening.

Lever/Snib

These upvc handles are also called "Snib handle sets" and come with a snib lock button at the top of the lever. If you do not have a dummy locking device then you can use this to secure the door. They are usually fitted with a Fullex 68PZ (that's 68mm between the spindle centre and lever or lock centre) door lock. We also stock a range of door handles with 68PZ from manufacturers like Ferco and Fab & Fix.

You can update your home by changing the door handles, whether you are replacing existing handles or installing new ones on doors that you have built. There are a variety of door handles made of upvc that include traditional levers on backplate, curved or straight short latches and knob handles with dummy handles for multi point locks which are ideal for French doors.

Lever on backplate handles are usually rectangular, but there are also circular or oval shaped models that are referred to as rose door handles. These kinds of door handles are equipped with an a knob or lever on a backplate that sits behind the knob or lever and is often referred to as the rosette, however certain back plates can be detached to be concealed for fixing.

The handles are available in various finishes, including chrome and coloured finishes, to be matched to your door and hardware such as knobs, hinges and bolts. Some handles are supplied with grub screws that aid in the secure attachment of the lever or knob to the spindle. Other handles are supplied with bathroom spindles that can be used to operate bathroom locks. They include a thumbturn turn and release mechanism, perfect to use on doors for bathrooms.

Mortise

If your front door's uPVC handle is stuck in the open position, the reason is likely to be due to the tubular latch. There may be a few reasons for this, the first being a simple lack of lubrication on the latch plate. This can be corrected easily by simply opening the door and spraying lubricant over the window handle replacement and lock. It could also be that the latch has come loose from the backplate. This is a more complex issue that requires the help of the assistance of a specialist.

A multipoint handle system is the ideal solution to stuck door handles. These handles are mounted through the faceplate and operated with the use of a key or thumb turn knob that triggers the cam that locks the deadbolt. The handles come in different sizes to fit various types of uPVC door [Redirect-Java] and in a variety of attractive finishes that are compatible with the hardware that is currently in use. These handles are available online or from the local locksmith. They are easy to install and come with clear directions.

You'll have to know your PZ size of your cylinder in order to select the right replacement upvc door handle; Full Article, handle set. This is the measurement in millimetres that lies between the outer edge of the door frame and the centre of the handle hole. You'll also need the type of lock for your door, whether it's a mortise or hook lock. The most efficient way to locate the correct handles after you have the measurements is to use the filter for brands on the website. This will help narrow down your options and then you'll be able to select the correct size.

A typical set of handles includes the handle unit, a pair of different length screws, drill guides and installation instructions. Smart versions, like the Igloohome Smart Mortise 2+ include a mortice lock complete with a keypad. These are more sophisticated devices and are best suited for professional installers or very skilled DIYers. Some handle sets include a variety of accessories, like weather strips that can be used to enhance the appearance of the door.