Reasons Your fiat 500 replacement key cost 500 Key Fob Won't Work

A key fob from fiat 500 lost key 500 makes it easy to open doors and start your car. There are a variety of reasons why the key fob might stop working. These include a dead battery damage to the receiver module, water issues, and interfering.

This listing is for an NEW replacement fiat stilo key Flip Key Remote - similar to the Ilco brand that needs to be programmed professionally by a local automotive locksmith (click here to search for a Locksmith Search). It includes trunk, lock and unlock buttons.

Dead Coin Battery

A dead battery is the most common reason for your 500 key fob not functioning. Modern key fobs have a very limited range of operation, and must be within some feet of the vehicle to operate. If you are further away from your car and push the keyfob button it will not respond and display the message "Key Fob Not Detected".

If this happens, replace the battery in the coin cell (Part number CR2032) with a new one from a reliable brand like Panasonic, Duracell, or Energizer. You can find them in your local hardware store, or on the internet.

After you've replaced the coin cell battery You can test it by standing close to your fiat key cutting 500 and pressing the buttons. The car should blink its parking lights, and the key fob will operate the lock and unlock switches.

If the fob's key doesn't function after replacing the battery, it could have water damage that prevents it from connecting to the receiver module inside your vehicle. Water damage can happen in many ways, such as the simple splash or submerging the key fob saltwater at the beach. If you believe your fob was exposed to water, put it in a bag of rice to draw out the moisture. If that doesn't work your fob is likely to require reprogramming by a professional auto locksmith or the dealer.

Water Damage

Although the fob is equipped with rubber seals that keep water out of the chip's electronic circuit the device, submerging it into the ocean or washing it in a machine could cause water damage. Saltwater can cause the circuit board to short and then cease to function. Getting the fob wet is not an ideal choice but if you accidentally drop it in a glass of water or forget to remove it from your pocket before you run the washing machine and you don't have a chance, don't give in.

First, remove the battery from the fob. Before replacing the battery, clean the electronic chip using isopropyl or a similar product. Test the fob next to determine if it's working. If the fob doesn't work, it may have to be changed. This is typically handled by a professional or dealer auto locksmith.

If the key is newer and was not programmed to your car, it will likely need to be replaced completely. This is an easy process that can be completed by a professional automotive locksmith. The locksmith will require the key to be cut to match your car's ignition. The locksmith also needs to program your fob into the car's system. This is a fast and affordable process that can be completed in the same day.

Receiver Module Issues

One of the simplest reasons why your 500 key fob might stop working is because it's out of range. The remote usually has 30 feet of range or less and if it's far from your vehicle, it will not respond to your commands. It's easy to remedy this by moving your remote closer to your vehicle until it responds.

If your fob won't work after replacing the battery inside the coin, which is also known as a "button", "watch" or "button", it may be due to a malfunction on the internal circuit board. In the majority of cases, reprogramming your fob will fix the problem. You can find instructions on how to do this for the majority of automobiles by searching YouTube or consulting the owner's manual.

It may be necessary to replace the clips made of metal that hold the coin batteries in place. If they lose tension, it can prevent the coin battery from being properly seated, and this will cause the remote to malfunction.

In rare cases the fob may be out of sync with your vehicle because of software or hardware problems. This can be a major problem, but you can usually resolve this issue by visiting a local dealer or auto locksmith to have them reprogram your fob for you. In certain instances it is possible that the software will require reinstallation to your body control modules.

Interference

Interference can also cause the key fob to not be able to receive or transmit a signal. This could happen if the key fob is close to an electronic radio transmitter (cell phones or radar detectors) or another source of electromagnetic radiation. The key fob might not function because of a problem to the buttons water damage or damage to the internal chips.

If your key fob suddenly stopped working, or if you have tried everything at home to fix it (e.g. You may have a faulty 500 receiver module If you've tried replacing it with a battery, reprogramming or using a spare car key fiat 500 key fob. The receiver module, which is located under the dashboard, receives radio frequency signals from your key fob. It converts the signals into electronic commands which are then processed by the vehicle.

There is a straightforward method to reset the 500's onboard system, including the keyfob. Disconnect the battery for 15 minutes by taking off first the negative cable and then the positive cable. Then, reconnect the battery. This will eliminate any remaining electrical charge and restart the car's computer system, which could help get your key fob working again. If the problem persists, you should consult an experienced technician. They will be able to identify the root cause of your issues.